Pros and Cons of Stamping Concrete

Pros and Cons of Stamping Concrete 

Every time you think about doing a common floor it is important to make calculations and even when it comes to polished concrete prices may vary from place to place. There are advantages and cons that should be measured before anything is done. Prices are based only and solely on the ground of value and labor to put it, which we should face it, we are a very serious mistake, as we shall show.

Comparing common floors andcement decorative concrete

To calculate the real value of the common floor versus the cement decorative concrete, we must first calculate how much we will spend with the needed materials and workmanship to the subfloor, and only from then, we add the value of the floor mortar, manpower grout placing and finishing, which happens to cost as well.

Example: In an area of ​​100m2, a mason would charge at least $ 12.00 per square meter ( $ 1,200.00), more sand, stone and cement worth approximately $ 1,500.00. You can also visit our top articles here for more information here. After this we have the mortar of approximately $ 400.00. Plus a reasonable floor in the individual amount of $ 18.00 in a film of 110 square meters (including footnotes) that goes back over $ 1,980.00, still missing the grout ($ 100.00) and hand value of work around $ 35.00 per square meter ( $ 3,500.00).

In addition all these values, we will have a total of  $ 8,980.00, which divided by 100 square meters, would give us a total cost of $ 89.80 per square meter with a simple floor, but if you wantcement decorative concrete you will be able to spend less cash and most times get a result that will last for much longer and will look even prettier. You will definitely enjoy the results provided by concrete driveways Melbourne.

Pros and Cons of Stamping Concrete

Cost of cement decorative concrete

In the case of stamped concrete, the client provides only the sand, stone and cement would spend the subfloor, the vessel example above $ 1,500.00, and the concrete driveways melbourne comes to manpower, products, fibers, sealants, resins, etc., at an average cost of $ 42.00 per square meters, which would give a total of $ 4,200.00. When you need to know more you can visit this link: here. If you are able to research prices then you will be able to save even more cash.

Added values ​​will have a total of $ 5,700.00, ie a cost of R $ 57.00 per square meter.

The advantages ofconcrete driveways Melbourne with cement decorative concrete

Beyond economics (37% on average), the concrete driveways melbourne can make up to 250 square meters of stamped concrete a day, as time and site conditions, while a mason cannot put more than 50 square meters on without grout, etc.

In stamped concrete floor, you gain in beauty, durability, speed and especially in the savings at the end of the duties. The concrete driveways Melbourne is indeed able to provide high quality results that will indeed look nice and pretty. Contact a trusted worker and have great results quickly.


3 Methods of Decorative Aggregate Exposure for Beautiful Polished Concrete

A developing pattern in adaptable, lovely ground surface arrangements that can likewise endure forever is the utilization of polished concrete. To accomplish such visual feel, the polished concrete exposed contractor first takes a gander at the concrete itself.

Working with Concrete

There’s a period respected saying about cement, whether handled or not, that it is reliably conflicting. Each and every pour will be unique in relation to the following, with varieties in shading, splitting and general levelness. Be that as it may, the general objective is for the floor’s evenness to be as even as could reasonably be expected, while pouring another piece, and in addition setting up the surface of a current chunk for wrapping up. Find out more information in this site.

Working with existing aggregate concrete chunks, results are controlled by the nature of the current cement. Shading varieties, pollutes, breaks, examples left by past floor covering, stains, nail gaps, fixed territories and evenness all influence the recently cleaned appearance.

3 Concrete Polishing Methods

The driveways Melbourne polishing process as a rule incorporates pounding down the surface to uncover diverse levels of total inside of the solid or the expansion of embellishing totals, for example, reused glass, arranging stone, nails, nuts, fasteners, ocean shells and others, seeded into the surface for enlivening purposes. There are three regular total decisions to consider with regards to polished concrete floors:

  1. Cream Polished or Surface Cream:

The top layer of the solid is produced using troweled bond glue that contains the concrete fines of the blend. Just 1/32 – 1/64-inch is expelled from the section surface, bringing about next to zero total introduction. This is a well known, efficient style; the cream is the purest, most predictable in shading, has the least blemishes and can be recolored any shading.

  1. Salt and Pepper:

The layer just underneath the cream produced using fine total – sand and little stone that gives the solid a “salt and pepper” look. To accomplish this look, 1/64 – 1/8-inch of the cream is uprooted by pounding the surface, uncovering little measures of medium total haphazardly all through. The perfect time to begin the crushing procedure is inside of 7 days of pouring the solid section, which uncovered only the appropriate measure of total.

  1. Uncovered Aggregate:

The layer beneath the cream and salt and pepper produced using coarse total inside of the cement decorative concrete. To achieve this layer, 1/8 – 1/4 – inch is ground from the surface, evacuating the main two layers. This procedure ought to begin very quickly after a solid chunk has been poured to inside of 3 days of pouring to accomplish the total presentation craved. Course total comes in three sizes: little, medium and extensive.

Subsequent to accomplishing the kind of total concrete polishing introduction, the concrete is polished to a sought clarity of reflection. 1) ground to a level sparkle, 2) sharpened to refined even appearance, 3) semi-cleaned, for fresh, smooth look or 4) profoundly cleaned, for a mirror

Check out some polished concrete examples here:



There is no place like home. After a hard day’s work, we always look forward to going home and take our rest with our family. In approaching our house, we are welcomed with the opening of the gates and the beauty of our driveways leading to our garage or carport. We don’t want to spoil the moment with uneven pavements or even cracked cements. It will add headache instead of peace of mind. In Melbourne, Australia, concrete driveways are a common sight. They make sure not a single mud or dirt enters their abode. In this article, we will discuss the differences between exposed aggregate and decorative concrete so that you can decide on what to use on your driveway.

  1. Exposed aggregates and decorative concrete are both very durable. The former may be described as a mixture of minerals just like mixed or sand gravel that can be modified by adding color or texture while the latter has a smooth finish to avoid the dangers of slipping or tripping.
  2. Exposed aggregates come in different colors while decorative concretes have a flat finish but can be designed and colored. This is because exposed aggregates come in a variety of natural mineral colors and has a high value when it comes to On the other hand, decorative concretes can be enhanced by stamping and other treatments.
  3. Exposed aggregates will take a long time to finish or construct while decorative concretes are easier to apply. It will take almost a day pouring and smoothing the surface and spraying it with special chemicals to make the top durable and long lasting. The other one is easily poured and smoothed, and it takes only hours to dry and finish. Additional decorative treatments can be applied later at the discretion of the owner.
  4. Exposed aggregates and decorative concretes are both durable but may be affected by natural and man-made events. Both the surfaces can be sealed for longer protection, but exposed aggregates are prone to different weather conditions. When pebbles or small stones start to disintegrate or break, the problem cannot be reversed. Decorative concretes, on the other hand, are prone to crack or break due to a too-heavy load or accidentally falling heavy objects.
  5. Exposed aggregates are difficult to maintain while concrete decoratives are easy to clean. Foreign objects like leaves, sand or dirt can easily enter the gaps, and it is hard to remove them unless you use a powerful water hose. When you use it every day, it can create holes and will become a problem, unlike the decoratives that you can scrub or wash with ease as long as there are no cracks in between.

When you look again to the concrete driveways in Melbourne, you will really appreciate their elegance and beauty since it’s an important part of the homes. Whether going out or coming in, there is a sense of deep appreciation for these two wonders in construction.

More info in this link: